English  |
| Quantity: | |
|---|---|
Disposable Cutlery Tableware Injection Molding Machine for Plastic Fork/Spoon
项目 ITEM | 单位UNIT | SZ—1300A | |||
注射装置 INJECTION UNIT | |||||
螺杆直径 | SCREW DIAMETER | mm | 35 | 40 | 45 |
螺杆长径比 | SCREW LID RATIO | L/D | 24 | 21 | 18.7 |
理论注射容积 | THEORETICAL SHOT VOLUME | CM3 | 173 | 226 | 286 |
注射质量(PS料) | SHOT WEIGHT(PS) | g | 158 | 206 | 260 |
注射压力 | INJECTION PRESSURE | Mpa | 235 | 180 | 142 |
理论注射速率(PS料) | THEORETICAL INJECTION RATE(PS) | g/s | 110 | 143 | 181 |
塑化能力(PS料) | PLASTICISING CAPACITY | g/s | 13.8 | 19.7 | 27.1 |
螺杆驱动扭矩 | SCREW TORQUE | N.m | 740 | ||
螺杆最高转速 | MAX.SCREW ROTATE SPEED | r/min | 250 | ||
洼射行程 | INJECTION STROKE | mm | 180 | ||
合模装置 CLAMPING UNIT | |||||
合模力 | MAX.CLAMPING FORCE K | KN | 1300 | ||
移模行程 | MAX.OPENING STROKE | mm | 400 | ||
拉杆有效间距(VxH) | SPACE BETWEEN TIE BARS | mm | 420×420 | ||
允许模厚(MIN-MAX) | MOULD HEIGHT | mm | 160-440 | ||
模板最大开距 | MAX.DAYLIGHT | mm | 840 | ||
液压顶出力 | EJECTOR FORCE | KN | 31.4 | ||
液压顶出行程 | EJECTOR STROKE | mm | 100 | ||
液压顶出杆总数 | EJECTOR QUANTITY | 5 | |||
其它 OTHER | |||||
油泵电动机功率 | PUMP MOTOR POWER | KW | 13 | ||
油泵最高压力 | PUMP PRESSURE | Mpa | 16 | ||
料简加热功率 | HEATING POWER | KW | 9.2 | ||
加热区段 | HEATING ZONE | 4 | |||
机器外形(LxWxH) | SIZE | m | 4.7×1.25×1.85 | ||
机器净重 | NET WEIGHT | t | 4.3 | ||
油箱容积 | OIL TANK CAPACITY | L | 360 | ||
国际公认型号 | INTERNATIONAL DESIGNATION | 1300—410 | |||
Disposable Cutlery Tableware Injection Molding Machine for Plastic Fork/Spoon
项目 ITEM | 单位UNIT | SZ—1300A | |||
注射装置 INJECTION UNIT | |||||
螺杆直径 | SCREW DIAMETER | mm | 35 | 40 | 45 |
螺杆长径比 | SCREW LID RATIO | L/D | 24 | 21 | 18.7 |
理论注射容积 | THEORETICAL SHOT VOLUME | CM3 | 173 | 226 | 286 |
注射质量(PS料) | SHOT WEIGHT(PS) | g | 158 | 206 | 260 |
注射压力 | INJECTION PRESSURE | Mpa | 235 | 180 | 142 |
理论注射速率(PS料) | THEORETICAL INJECTION RATE(PS) | g/s | 110 | 143 | 181 |
塑化能力(PS料) | PLASTICISING CAPACITY | g/s | 13.8 | 19.7 | 27.1 |
螺杆驱动扭矩 | SCREW TORQUE | N.m | 740 | ||
螺杆最高转速 | MAX.SCREW ROTATE SPEED | r/min | 250 | ||
洼射行程 | INJECTION STROKE | mm | 180 | ||
合模装置 CLAMPING UNIT | |||||
合模力 | MAX.CLAMPING FORCE K | KN | 1300 | ||
移模行程 | MAX.OPENING STROKE | mm | 400 | ||
拉杆有效间距(VxH) | SPACE BETWEEN TIE BARS | mm | 420×420 | ||
允许模厚(MIN-MAX) | MOULD HEIGHT | mm | 160-440 | ||
模板最大开距 | MAX.DAYLIGHT | mm | 840 | ||
液压顶出力 | EJECTOR FORCE | KN | 31.4 | ||
液压顶出行程 | EJECTOR STROKE | mm | 100 | ||
液压顶出杆总数 | EJECTOR QUANTITY | 5 | |||
其它 OTHER | |||||
油泵电动机功率 | PUMP MOTOR POWER | KW | 13 | ||
油泵最高压力 | PUMP PRESSURE | Mpa | 16 | ||
料简加热功率 | HEATING POWER | KW | 9.2 | ||
加热区段 | HEATING ZONE | 4 | |||
机器外形(LxWxH) | SIZE | m | 4.7×1.25×1.85 | ||
机器净重 | NET WEIGHT | t | 4.3 | ||
油箱容积 | OIL TANK CAPACITY | L | 360 | ||
国际公认型号 | INTERNATIONAL DESIGNATION | 1300—410 | |||
